Bachelor of Science in Engineering (B.S.E.) - Major in Engineering
Mission
The mission of the Bachelor of Science in the Engineering Program is to provide relevant, high-quality undergraduate engineering education in a traditional collegiate atmosphere while serving as engineering resource for West Tennessee. The faculty enhances the engineering profession by conducting applied research and providing public service in their fields of expertise.
Program Educational Objectives
The following program educational objectives have been adopted by the engineering faculty of the Department of Engineering to meet the criteria established by the Engineering Accreditation Commission of ABET, http://www.abet.org. After graduation from our program, engineers will be able to:
- become successful professionals that recognize the complexity of a modern global society and meet the diverse needs of a broad spectrum of employers.
- serve and contribute to the engineering needs of West Tennessee and the broader regional, state, national, and global markets.
- continue to grow professionally, including leadership and communication skills, through life-long learning activities such as becoming a licensed professional engineer, pursuing graduate study, participating in continuing professional education, and active membership in professional engineering societies.
Bachelor of Science in Engineering
In support of the university’s mission, the Department of Engineering offers the Bachelor of Science in Engineering (B.S.E.) (accredited by the Engineering Accreditation Commission of ABET, http://www.abet.org) with a concentration in one of the following:
Civil Engineering (6511)
Computer Engineering (6517)
Electrical Engineering (6512)
Manufacturing Engineering (6515)
Mechatronics Engineering (6516)
Engineering majors learn the fundamentals of engineering with an emphasis on problem solving, design and integrated systems, from courses in engineering, mathematics, and the physical sciences, while also taking courses in communications, fine arts, humanities, and social and behavioral sciences. During the junior and senior years, students take a cohesive set of upper-division engineering courses that together provide depth of knowledge and design content in the chosen engineering concentration. Upon graduation, the engineering concentration is recorded on the student’s permanent record, i.e., on the student’s final transcript.
Designed for completion in four years (or five years when combined with the engineering Cooperative Education Program), the B.S.E. incorporates the latest guidelines from the professional engineering world as well as the advice and guidance of UT Martin’s Department of Engineering Industrial Advisory Board. The B.S.E. degree program draws from the classroom, laboratories, and real-world experiences, using the rich resources of the university, the engineering faculty, and the professional engineering community to prepare students for the engineering world of today and the future.
As a result of the focused efforts of the university, government and industry partnership that led to its development, the comprehensive B.S.E. program offers an engineering degree that is uniquely relevant to today’s students and employers. Graduates are prepared for practice as professional engineers. They have acquired the foundation for maintaining professional competence throughout their careers and they have the skills and experiences needed to move quickly into leadership roles in today’s engineering and management environments.
Students who desire the option of further study at the graduate level are well prepared to continue their engineering education at the master’s and doctoral level. Some students may choose to follow their engineering degree with an M.B.A. degree. Also in today’s highly technological world, this comprehensive engineering degree program provides an excellent core, when combined with the appropriate biology and chemistry courses, for a pre-medical curriculum.
All UT Martin engineering students develop a firm foundation in engineering science and in engineering design, with a concentration in civil, computer, electrical, manufacturing, or mechatronics engineering. Our students also gain real-world engineering job experience; acquire knowledge in fundamental business concepts; develop an understanding of ethical, political, and societal issues; and build their skills in written and oral communications, teamwork and leadership.
Students are required to complete a senior design project (or capstone project) during the senior year. Senior design projects require previously gained knowledge obtained from a culmination of engineering courses. It integrates and applies the knowledge and skills acquired throughout the courses of the engineering program. Engineering advisor and department approval are required to register for senior design.
Students are also required to pass the Fundamentals of Engineering (FE) exam administered by the National Council of Examiners for Engineering and Surveying (NCEES). The National Society of Professional Engineers (NSPE) requires passing the FE exam as one of the initial steps in becoming a licensed engineer, also known as a Professional Engineer (PE). Graduating with the B.S.E. from UTM is a great start to an engineering career. For more information about the FE and becoming a PE, visit https://ncees.org/ and https://www.nspe.org/.
Additional information about the B.S.E. program may be obtained by visiting The University of Tennessee at Martin website, www.utm.edu, and viewing the Department of Engineering web pages.
Designation of a Minor
The B.S.E. does not require the completion of a minor.
An engineering student may declare a minor in a non-engineering subject area and have the minor listed on the permanent record under the following conditions:
- minors must be officially approved and described in the university catalog. No unofficial minors will be recognized.
- courses taken to satisfy the minor may also be used to satisfy engineering degree requirements, provided that the courses are a part of the engineering degree requirements even if no minor were declared.
- the intention to complete a minor must be declared at the time of application for a degree if the minor is to appear on the final transcript.
Admission, Retention and Graduation Requirements
In addition to the university’s admission requirements, a student must meet one of the following requirements to be provisionally admitted to one of the engineering majors:
- obtain an ACT math sub-score of 25 or higher or;
- have completed at least one semester of college trigonometry with a grade of C or better.
These requirements apply to freshmen, transfer students, and students desiring to change majors.
Full admission to one of the engineering concentrations requires that a student complete eight core courses with 1) a grade C or better, and 2) a minimum GPA of 2.00 computed using all attempts in a course.
The Core 8 courses are, by concentration:
Civil: MATH 251 , MATH 252 , MATH 320 , PHYS 220 , PHYS 221 , ENGR 121 , ENGR 220 , ENGR 241
Computer: MATH 251 , MATH 252 , MATH 320 , PHYS 220 , PHYS 221 , ENGR 232 , CSCI 222 , CSCI 325
Electrical: MATH 251 , MATH 252 , MATH 320 , PHYS 220 , PHYS 221 , ENGR 231 , ENGR 232 , CSCI 221
Manufacturing: MATH 251 , MATH 252 , MATH 320 , PHYS 220 , PHYS 221 , ENGR 121 , ENGR 220 , ENGR 241
Mechatronics: MATH 251 , MATH 252 , MATH 320 , PHYS 220 , PHYS 221 , ENGR 121 , ENGR 232 , ENGR 241
Students who have not gained full admission to one of the engineering majors cannot take upper-division (numbered 300-499) engineering courses, with the exceptions of ENGR 315 Engineering Analysis, and ENGR 380 Engineering Economy.
Prior to qualifying for full admission to one of the engineering majors, a student pursuing an engineering major receives academic advisement from an engineering faculty member and is allowed to take any lower division (numbered 100-299) engineering course if the student 1) meets the course prerequisites and corequisites and 2) meets the department’s prerequisite grade rule.
An engineering student must earn a minimum grade of C in required economics, engineering, mathematics, and science courses that are prerequisites for another course in the curriculum prior to taking the course that requires the prerequisite; e.g., a student may not take MATH 252 until the student has earned a grade of at least a C in MATH 251 and may not take ENGR 241 until earning minimum grades of C in MATH 252 , PHYS 220 and ENGR 121 . Prior to graduation, a grade of C or better must be earned in all economics, engineering, mathematics, and science courses used to fulfill degree requirements.
Cooperative Education and Internship Programs
The Department of Engineering Cooperative Education (Co-op) and Internship Programs are designed to provide the services of young men and women committed to pursuing careers in Engineering to the West Tennessee region and beyond. Productive, practical engineering work experiences are a fundamental part of the student’s education. The concept recognizes the value of the three-way partnership between the UT Martin Department of Engineering, the employer, and the student.
Co-op Program
The engineering Co-op program is offered as an educational enhancement to the B.S.E. program. To complete the Co-op program, a student works full-time in progressive engineering work assignments for at least three semesters (the equivalent of one year) prior to the student’s senior year. Students enrolling in the Co-op program gain the benefits of a planned progression of work experiences which complement and enrich their engineering studies on campus. Participants gain insight into the engineering work world, apply their insights from the real world to their studies, grow in understanding of their own interests and career objectives, and advance in professional maturity.
Co-op positions must be full-time engineering work experiences supervised by degree holding engineer for a period of at least ten consecutive weeks within each semester. During the full-time work semesters, the College of Engineering and Natural Sciences considers the student full-time. Co-op work assignments are paid positions, and students are able to help finance their education while gaining real-world engineering experience.
After completing all the B.S.E. freshman year course work, an engineering student with a cumulative GPA of at least 2.50 may elect to participate in the engineering Co-op program. A transfer student must complete at least one full-time academic semester at UT Martin and must have a minimum cumulative GPA of 2.50 to qualify.
Co-op work periods are tailored to meet the needs of the student and employer.
Internship Program
Intern positions must be full-time engineering work experience supervised by degree holding engineer for a period of at least ten consecutive weeks. During the full-time work semesters, the College of Engineering and Natural Sciences considers the student full-time. The internship should be planned no sooner than the summer between the junior and senior year.
Students pursuing the Bachelor of Science of Engineering (B.S.E.) have the following two options concerning fulfilling the internship requirement:
- complete at least a one-semester internship as part of the B.S.E. degree requirements. The internship will be scheduled when the student is within three semesters of graduation; or
- complete three co-op semesters. Completion of the co-op program will substitute for the required internship.
Facilities
Instructional facilities of the department include: two dedicated, computer labs for engineering students, with a wide range of software that include AutoCAD, Autodesk Civil 3D, Autodesk Inventor, Autodesk Revit, Autodesk Inventor CAM, LabVIEW, MATLAB, PSpice, and the Microsoft Office Suite; a wide range of laboratories to support an engineering hands-on education: Asphalt Lab, Electrical Labs, Embedded Systems and Linear Controls Lab, Environmental Lab, Fluid and Hydraulics Lab, Geotechnical Lab, Industrial Controls and Robotics Lab, Material Lab, Mechanical Lab, Surveying equipment Lab, Structural Lab, Vibrations Lab, students project rooms; and student study rooms.
Student Organizations
There are currently four student chapters of professional societies in the Department of Engineering: The American Society of Civil Engineers (ASCE), the Institute of Electrical and Electronics Engineers (IEEE), the Society of Automotive Engineers (SAE), and the Society of Manufacturing Engineers (SME). Each society has a faculty adviser and engages in activities and projects of common interest to the membership. Students are encouraged to participate in one or more of these organizations for professional growth.
Overview of Degree Requirements
|
General Education Requirements
|
38 hours
|
|
Engineering Program Requirements
|
26* hours
|
|
Concentration Requirements
|
64 hours
|
|
Minor (if required)
|
Not required
|
|
Electives (or other program requirements etc.)
|
Not required
|
|
TOTAL
|
128 hours
|
*This number (26) assumes that up to 14 credit hours from the engineering program requirements (40) can be taken to satisfy general education requirements (38). The following courses CHEM 121 (4), ECON 201 (3), MATH 251 (4), PHYS 220 (4), or PHYS 221 (4) may be taken to satisfy both general education requirements AND engineering program requirements. If a student does not complete these courses as part of general education, then the degree will require more than 128 credit hours to complete.
Bachelor of Science in Engineering (B.S.E.)
The Department of Engineering at UT Martin provides students with the tools needed to excel in a competitive and challenging field, opening the door to a wide range of professional careers. Our programs emphasize the fundamentals of engineering design, exploring theoretical foundations through practical applications. Equipped with modern technology, hands-on laboratories, and professors invested in student success, our engineering degree programs offer extensive opportunities for growth and exploration.
For more information about the engineering major, please contact:
Department of Engineering
137 Latimer-Smith Engineering and Science Building
203 Hurt Street
Martin, TN 38238
engineering@utm.edu
(731)881-7571
Return to: